Pentair Water Pool and Spa Incorporated disclaims proprietary interest in marks and names of others. Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. The trademark IntelliTouch, is a trademark of Pentair Water Pool and Spa. Information in this document is subject to change without notice. © 2005 Pentair Water Pool and Spa, Incorporated.ġ0951 West Los Angeles Ave., Moorpark, CA 93021 Īll rights reserved. IntelliTouch ScreenLogic User’s Guide (P/N 520493)
#Resetting pentair screenlogic manuals
Web site: visit Related IntelliTouch Manuals Pentair IC40 problems come in the above nature and can be solved through the solution provided.Sanford, North Carolina (8 A.M. After connecting Alexa to your Pentair IntelliTouch or EasyTouch control system (with ScreenLogic) in a few simple steps, just say commands like 'Alexa, ask Pentair Pool to turn on my Waterfall.', or 'Alexa, ask Pentair Pool what my pool temperature is.', or 'Alexa, ask Pentair Pool what my pool status is' Here are examples of how you can use. Diagnose the problem and rectify accordingly. No Power – Fuse is open, no AC power, or issues with wiring. Possible Cause of No or Little Chlorine ResidualĬold Water Light (Red) – Water is below 52 degrees F. Wait for about one day to recheck the IC40 to ensure that it is reading good or green salt.
![resetting pentair screenlogic resetting pentair screenlogic](https://cdnb.c3dt.com/preview/574987-com.app.pentair.jpg)
#Resetting pentair screenlogic professional
Note: Before you add a huge amount of salt, have a professional inspect your facility. Add the right amount of salt according to the chart in your manual. Check the level of salt in your Spa or pool. The salt level is extremely low and your device is no longer releasing chlorine. Wait for at least one day and then recheck the system to ensure that the IC40 is reading good salt or green. Check the level of salt in your facility and add the right amount salt according to the size of your pool or spa. Yellow means that the level of salt is slightly low. Leave your pool for one day to allow the pump to circulate and mix the water and then allow your IC40 to check the level of salt again. Repeat the process until you get the desired concentration. If the level is pretty high, reduce it by draining some of the water out of your pool and add fresh water. Inspect the level of salt in your spa or pool. In fact, the salt level might be excessively high. This doesn’t mean that your pool has the proper level of salt.
![resetting pentair screenlogic resetting pentair screenlogic](https://f01.justanswer.com/b1vnH0jy/e6b3a5d3-9ce8-4c6d-bbe2-bd6cf6b932f4.jpeg)
Hence, wait for about 2½ minutes to allow the Pentair IC40 to properly sense the level of salt.Īfter that, 1 of the 3 LED’s will be illuminated displaying salt level. The 3 salt levels LED’s Red, Yellow, and Green are designed to repeatedly flash for the about 2 minutes after every startup. In case the switch can no longer work, it’s time to replace it. If you detect insufficient flow, then uninstall the cell and inspect the flow switch situated in the front part of the cell to guarantee proper operation. If the light is red, that means that there is insufficient flow via the cell for the right operation.Ĭheck to ensure that the pool pump is switched on and the water is flowing freely. That means that proper flow is passing via the cell. The light should be green under normal operations. Just press and grip the “More Button” for 3 seconds and the device will go into “Status Check Mode” and show on the bottom 5 output percentage LEDs in 2000-hr multiple, the amount of time your gadget has operated (20 percent represents 2000 hrs. You can manually check life and cell usage at any moment.